Follow US:

How do you pronounce silicone resin in English (1 out of 648).

Captions are loading...

Translation of silicone resin

Translate silicone resin to Go

IPA (International Phonetic Alphabet) of silicone resin

The International Phonetic Alphabet (IPA) is an alphabetic system of phonetic notation based primarily on the Latin alphabet. With phonetic transcriptions, dictionarie tell you about the pronunciation of words, because the spelling of an English word does not tell you how you should pronounce it. Below is the phonetic transcription of silicone resin:
/sɪləkown ɹɛzən/

Derived Form of silicone

noun
plural: silicones
Noun
1
any of a large class of siloxanes that are unusually stable over a wide range of temperatures; used in lubricants and adhesives and coatings and synthetic rubber and electrical insulation
Synonymssilicone polymer,
Hyponymsbouncing putty,
Hypernymspolymer, siloxane,
Partsatomic number 14, Si, silicon,
Type ofpolymer, siloxane,
Typesbouncing putty,

Derived Form of resin

noun
plural: resins
Noun
1
any of a class of solid or semisolid viscous substances obtained either as exudations from certain plants or prepared by polymerization of simple molecules
Synonymsrosin,
HyponymsEast India kino, natural resin, synthetic resin,
Hypernymsorganic compound,
Type oforganic compound,
TypesEast India kino, kino gum, Malabar kino, natural resin, synthetic resin,
See alsoresinate, resinated, resinlike,

silicone resin on Youtube

  1. I only have the silicone putty to make the molds, and UV resin needs light to cure, so I'll have to patch two sides of
  2. in silicone then poured epoxy or resin in the mold to see if it sounds the same.
  3. We're going to try making a silicone mold of the record, and then cast it and resin to see if we can get a playable copy.
  4. Where I have these marks in the silicone this is just in an effort to make sure that the resin doesn't run down
  5. I put a dark blue violet toned UV resin into a silicone mold and cured it to make the pupil part.
  6. Apply a thin layer of resin to a silicone mould and allow it to firm up
  7. I'm adding a pinch of mica powder to my first resin pour to cover the base of a round silicone coaster mould
  8. This can only mean one thing which is that Puni gel is not resin but actually silicone
  9. And this is a silicone based primer obviously it's called it porefessional so because of the silicone
  10. We will need: epoxy resin and resin hardener.
  11. This is silicone, so we'll put SIL for silicone.
  12. Halloween the moon mass masquerade silicone mask oh the smell of these Chinese silicone things is abhorrent
  13. I'm using two silicone cube moulds to create a mould. The smaller of the two is pre-filled with cured resin to give it some weight.
  14. When the first pour of resin has firmed up, add a little more resin then place the sun and moon into position
  15. and silicone base, its an emulsion where the water phase is surrounded by silicone.
  16. my silicone brush this is a prima spinnerbait silicone brush and it's
  17. epoxi resin and silicone gel. The motivation behind this project is basically
  18. Types of silicone/ whether or not silicone is included, polymer, silica, alumina, and isododecane.
  19. (Resin = UV cure resin) I'm Resin.Please call me Resico
  20. This is 3mm PVC Foamex, which the resin does not stick to. You could use a surface covered in shiny parcel tape, or a silicone mat.